Well-ventilated steel of venting design for molded parts
Well-ventilated steel is a sintered alloy, iIt is a porous material sintered with spherical particle alloys, the pore size is 7-10μm and the strength is poor, but the texture is loose which allow the gas to pass through. Placing a piece of well-ventilated steel on the part that needs to be vented can make venting well. However, the diameter of the bottom vent hole should not be too big to prevent it from being squeezed and deformed by the cavity pressure, due to the low thermal conductivity of well-ventilated steelsteel, it cannot be overheated, otherwise, it is easy to cause decomposition products to block the pores.
Features of well-ventilated steel:
1. The density is small and the specific strength is big.
2. Good energy absorption.
3. Good vibration damping effect.
4. Large specific surface area, a quarter of the tissue is through holes.
5. Original hardness of well-ventilated steel: pre-hardened to 350~400HV (35~40HRC).
Well-ventilated steel characteristics:
1. Reduce injection pressure and pressure holding time;
2. Reduce and eliminate the internal stress of the molded parts to prevent the deformation and warpage of the product;
3. It can solve and alleviate the difficult forming issues due to gate deviation, uneven wall thickness, and thin wall plastic parts.
4. The gas generated by the high temperature of the molding material and the defects such as scorching, flow marks, material shortage, and part deformation caused by rapid pressure accumulation in the mold cavity can be fully resolved;
5. Improve molding production efficiency and save production costs, so put well-ventilated steel in suitable place of the injection mold, the injection issue caused by the gas can be completely eliminated, making the molding process much better.
Making the well-ventilated steel tips:
1. Use H7/m6 to fix the well-ventilated steel with mold;
2. Milling, grinding, polishing, knocking, etc. are not allowed on the surface of the well-ventilated steel to avoid clogging of the vent holes, only make EDM;
3. Choose to install the well-ventilated steel in a flat position to avoid cutting;
4. Exhaust slot or vent holes must be opened on the bottom surface of the well-ventilated steel, and connect with the air;
5. The use of well-ventilated steel for exhaust air will leave the shape of ventilating micropores on the surface of the product, so the ventilating element can only be installed on the non-critical surface;
6. In order to prevent clogging of the ventilation holes, regular maintenance of the exhaust components is required during forming and production;
7. Breathable steel exhaust is not suitable for resins that require high-pressure injection molding, such as PC, PC+ABS, etc.; high-pressure injection molding will cause damage to the exhaust components
Vacuum venting mold design for plastic molded parts
Mar 23, 2022There are some regular venting way which are parting surface venting, insert venting, insert pin venting and well-ventilated steel, but there is a special way is vacumm venting, it will need vacumm...viewPin-point gate of plastic injection mold runner system design
Jan 24, 2022In order to get the best injection quality, the gate type must be selected carefully, the coommon gate tyeps are: direct gate, side gate, pin-point gate, sub gate,valve gate of hot runner etc. Among...viewGate position determination of plastic injection mold runner design system
Jan 17, 2022In the selection of gate location, the following issues should be paid attention to: 1. The gate position should be set at the maximum wall thickness of the plastic part, so that the plastic melt...viewWhat is the side parting and core pulling mechanisms with their function?
May 31, 2022When there are holes, cavities or cores on the inside or outside of the injection-molded plastic parts that are different from the opening and closing directions of the mold, the plastic parts cannot...viewDirect gate of plastic injection mold runner system design
Jan 19, 2022In order to get the best injection quality, the gate type must be selected carefully, the coommon gate tyeps are: direct gate, side gate, pin-point gate, sub gate,valve gate of hot runner etc. Among...viewPlastic injection mold common cooling gate
Feb 17, 20221. Straight-through cooling water gate: the straight-through cooling gate is the most commonly used gate for plastic injection mold, and it is also the most convenient type of cooling for processing....view